- #Utility bendix abs light issues drivers
- #Utility bendix abs light issues driver
- #Utility bendix abs light issues full
- #Utility bendix abs light issues software
“Any time you’ve got a vehicle in the shop, it’s also worth greasing the S-cam brake tubes and automatic slack adjusters: This quick process helps prevent rust and corrosion, and helps keep the slack functioning properly,” said Mark Holley, Bendix director of marketing and customer solutions – Wheel-End.
#Utility bendix abs light issues full
“Now is the time for fleets and owner-operators to prepare, not just with the goal of passing inspections, but to help make sure vehicles are running at their safest, and that today’s higher-level safety systems like full stability and collision mitigation are supported by optimally maintained brakes at the wheel-ends.”īrake Safety Week is part of CVSA’s Operation Airbrake initiative – an outreach and enforcement campaign that aims to reduce the number of highway crashes caused by faulty brake systems on commercial motor vehicles.
#Utility bendix abs light issues drivers
It's not always that easy but you never know.“So many of these out-of-service violations – situations that present actual hazards to roadway safety for the drivers and everyone around them – are preventable through proper maintenance practices and regular equipment examination,” said Fred Andersky, Bendix director – demos, sales, and service training.
![utility bendix abs light issues utility bendix abs light issues](https://db73q1dut0rlp.cloudfront.net/eyJ3aWR0aCI6NDM1LCJoZWlnaHQiOjQzNSwiZml0IjoiY29udGFpbiIsIndhdGVybWFya2VkIjp0cnVlLCJrZXkiOiJhc3NldHMvaW1hZ2VzLzM5NzgyNzUvcHJvZHVjdC8zNmMwODVkODY2MjhhZDk4Yzc4MDc2NTNmYTFmODJkMy5qcGciLCJ2ZXJzaW9uIjoyfQ==.jpg)
Spliced it back together and problem was fixed. Walked right to the #3 left wheel and started tracing the cable and found where it had broken right at a zip tie in plain sight. I finally gave up on that method and just started looking at the basics. I had a KW in the shop yesterday with an ABS fault and for some reason the laptop wouldn't connect to the Bendix system. They will probably only be on one rear axle, one on each side and the front axle. The sensors will have a small round cable coming out of the back of the brake spider and probably tied to the brake hoses all the way up to the valve.
![utility bendix abs light issues utility bendix abs light issues](https://docplayer.net/docs-images/50/15535584/images/page_19.jpg)
Maybe you could take a quick look at any sensor wiring that you can see.
#Utility bendix abs light issues driver
I know it's hard to get a mechanic to take troubleshooting advice from a driver so good luck. Check the connections at the main ABS relay valve and modulator valves (if the system has remote ones).ĭo they have any ABS software? If so they may be able to use it to diagnose the problem.ĭid you have a brake job or wheel seals replaced right before this started happening? Look for pinched, broken, loose wires on the wheel sensors and check the air gap between the sensor and excitor ring on each wheel.
#Utility bendix abs light issues software
That said, even without IH software they should be checking the basics on the ABS/Tract Cntrl system. They could maybe call a dealer and see if they can wring any info out of the service manager but he'll most likely tell them to bring it in. Unless your mechanics have had some IH training and literature those codes won't mean diddly.
![utility bendix abs light issues utility bendix abs light issues](https://cdn.carcomplaints.com/minisites/img/cadillac/service-stabilitrak.jpg)
You can't even add a switch into the multi-plex system without taking it to them to have it turned on. They like to make you bring it back to them for torubleshooting and repairs. It's not easy getting the IH software unless you are a huge customer and even then you still can't get the full meal deal. The mechanics are right about the software.